Pioneer SC-25 Betriebsanleitung PDF herunterladen (Seite 61)

recorder if you are unsure how to do this. Most

video recorders set the audio recording level

automatically-check the component’s instruc-

tion manual if you’re unsure.

5 Start recording, then start playback of

the source component.

Reducing the level of an

analog signal

The input attenuator lowers the input level of an

analog signal when it’s too strong. You can use

this if you find that the OVER indicator lights

often or you can hear distortion in the sound.

The attenuator isn’t available with digital

sources, or when using the Stream Direct

(ANALOG DIRECT) modes.

% Press to the receiver operation

mode, then press A.ATT to switch the

input attenuator on or off.

Using the sleep timer

The sleep timer switches the receiver into

standby after a specified amount of time so

you can fall asleep without worrying about the

receiver being left on all night. Use the remote

control to set the sleep timer.

% Press to the receiver operation

mode, then press SLEEP repeatedly to set

the sleep time.

30 min 60 min

Off 90 min

! You can check the remaining sleep time at

any time by pressing SLEEP once. Pressing

repeatedly will cycle through the sleep options

again.

! The sleep timer is valid for all zones. If

any zone is on, the sleep timer continues

functioning.

Dimming the display

You can choose between four brightness levels

for the front panel display. Note that when

selecting sources, the display automatically

brightens for a few seconds.

% Press to the receiver operation

mode, then press DIMMER repeatedly to

change the brightness of the front panel

display.

! You can also choose to turn the display off. In

this case, the FL OFF indicator lights.

Switching the HDMI output

Set which terminal to use when outputting

video and audio signals from the HDMI output

terminals.

The HDMI OUT 1 terminal is compatible with

the Control with HDMI function.

% Press to the receiver operation

mode, then press HDMI OUT.

Please wait a while when Please wait ... is

displayed.

The output switches among HDMI OUT ALL,

HDMI OUT 1 and HDMI OUT 2 each time the

button is pressed.

! The synchronized amp mode is canceled

when the HDMI output is switched. If you wish

to use the synchronized amp mode, switch to

HDMI OUT 1, then select the synchronized

amp mode on the TV using the TV’s remote

control.

Using other functions

About the Speaker B Link function

When 7.1ch + Speaker B or

5.1ch + SP-B Bi-Amp is selected for the

Speaker System setting (page 76) and the

Speaker B Link setting (HDMI Setup on page

53 ) is turned on, the setting of the played

speaker terminals switches automatically when

HDMI OUT is switched.

The settings switch as follows:

! HDMI OUT ALL – Switches to SP: A+B ON.

Sound is output simultaneously in the room

where the A speakers are located and in the

room where the B speakers are located.

! HDMI OUT 1 – Switches to SP: A ON. Sound

is only output in the room where the A

speakers are located.

! HDMI OUT 2 – Switches to SP: B ON. Sound

is only output in the room where the B

speakers are located.

Checking your system settings

Use the status display screen to check your

current settings for features such as surround

back channel processing and your current

MCACC preset.

1 Press to the receiver operation

mode, then press STATUS to check the

system settings.

The front panel display shows each of the fol-

lowing settings for three seconds each: Input

Source d Sampling Frequency d MCACC

preset d ZONE 2 input d ZONE 3 input d

HDMI OUT.

2 When you’re finished, press STATUS

again to switch off the display.

Resetting the system

Use this procedure to reset all the receiver’s

settings to the factory default. Use the front

panel controls to do this. Set MULTI-ZONE to

MULTI ZONE OFF.

! Disconnect the iPod and USB memory device

from the receiver beforehand.

! Set the Control with HDMI to OFF (see HDMI

Setup on page 53 ).

1 Switch the receiver into standby.

2 While holding down ENTER on the

front panel, press u STANDBY/ON.

The display shows RESET c NO d.

3 Select ‘RESET’ using PRESET k/l,

then press ENTER on the front panel.

The display shows RESET? OK.

4 Press ENTER to confirm.

OK appears in the display to indicate that the

receiver has been reset to the factory default

settings.

! Note that all settings will be saved, even if the

receiver is unplugged.

1 2 ... 56 57 58 59 60 61 62 63 64 65 66 ... 107 108

Kommentare zu diesen Handbüchern

Keine Kommentare

Pioneer SC-25 Betriebsanleitung Seite 61

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Software Pioneer SC-25